Exxus Vape Go Plus Concentrate Vaporizer

The Only Way To GO

The GO Plus Vaporizer is the latest wax concentrate device by Exxus Vape. This brand-new vaporizer features a coil-less quartz tank, manual/auto mode, a wide range of temperature control, and a magnetic attachment. It also includes other parts and accessories like a glass carb cap, a silicone tether, an OLED display, and LED lights. Strongly powered by a 5200mAh battery, the GO Plus uses a Type-C cable for fast charging capabilities. This new concentrate vaporizer will fulfill every puff!

How To Turn On/Off:

Before you turn on the GO Plus, ensure it has been fully charged. To start using the device, press its power button 5X rapidly to turn it on. The screen will show an introduction, which displays the Exxus logo. If you want to turn the GO Plus off, press the power button 5X again.

How To Change The Temperature:

What’s impressive about the GO Plus is its wide temperature range. To change the temperature to your desired heat level, press the (+) button to increase by 1°F and the (-) button to decrease the temperature. Adjust the temperature to your liking!

You can also change the temperature scale from Fahrenheit to Celsius. Hold the power and temperature buttons for two seconds to change the scale.

How To Get Started:

The GO Plus gives you the options of Manual and Automatic heating. To start Manual Mode, hold the power button and release it to stop. For Automatic Mode, on the other hand, press the power button 2X continuously. The device will then start preheating to your desired temperature. To stop Automatic Mode, press the power button 2X again.

How To Change Working Time Settings:

The OLED screen display visually shows the timer and the temperature. To change both settings, press (+) and (-) simultaneously for two seconds to adjust the working time. You can adjust your timer from 10 to 60 seconds.

How To Change Device Settings To Your Preference:

Once you have attached the coil-less quartz atomizer to the GO Plus base, the device will automatically detect the heating chamber and the concentrate button will appear on the screen.

The GO Plus allows you to turn the LED lights on and off—hold the power button and the (+) button for two seconds. You can also turn off the sounds by pressing the power button and the (-) for two seconds.

If you’d like to see the battery status of your device, press the power button once. The battery icon will show the remaining lifespan.

How To Charge:

When you unbox the GO Plus, charge the base for three hours. After the first charge, do not charge the device for more than three hours, as this could ruin the battery or wear down the lifespan.

While charging, the LED screen will show the battery life meter. When it reaches to four bars, the battery is fully complete.

How To Solve An Atomizer Error:

When the atomizer has an error, the LED screen will display “Check Atomizer”, and the device will beep 3X. To solve this issue, screw on the coil-less quartz tank properly. Ensure that the attachment is not too tight or too loose.

How To Solve An Overheating Issue:

When the GO Plus is overheating, the LED screen will show “Protect” and the device will beep 3X. To solve, make sure to not use the device. It is suggested to turn off the device and let it cool down.

How To Load The GO Plus:

To begin your dabs, fill the glass bubbler with water. It is recommended to fill only to a third of the bubbler. Ensure to not overfill pass the line marked maximum line. Next, screw in the heating chamber clockwise onto the base. Then, magnetically attach the glass bubbler to the base. After, select your desired temperature and timer settings to start your dabs. When you have adjusted to your liking, the device will beep, leading you to enjoy your vaporizing experience!

How To Clean The Go Plus:

After a dab session, you must always clean your device! First, you should clean the chamber by unscrewing it from the base. Then, use a cotton swab soaked with alcohol and gently remove any dirt or residue.

To clean the bubbler, remove it from the base and pour isopropyl alcohol into the mouthpiece until the unit is ¼ full. Next, rinse the alcohol out and pour water into the mouthpiece until all the alcohol has been flushed out. To remove water from the bubbler, blow through the mouthpiece and shake gently.

When cleaning the base, make sure to clean the screw connection with an alcohol soaked cotton swab. Then, allow it to fully dry before re-attaching the heating chamber.

What’s Included:

• (1) Exxus GO Plus Base
• (1) Glass Percolator
• (1) Silicone Tether
• (1) Glass Carb Cap
• (1) Coil-less Quartz Chamber
• (1) Packing Tool
• (1) Type-C Charging Cable

WARNING: Do not charge with a powerbank of 5V or higher. Do not charge in your car, and do not overcharge or use any other cable than what comes with your device. Failure to follow these guidelines could result in battery damage and/or frying of the internal system.